GarageChem Engine Chemistry Specialists Ask Us
Home Shop Ceramizator Technology How to Use Lab Results FAQ Contact Ask Us
Home/How to Use
Application guide

How to apply
Cerator

No disassembly, no flush, no special oil. The product goes in through the oil filler cap, and the engine builds the ceramic layer itself over the first few hundred miles of driving.

01

Warm up the engine

Run the engine until it reaches normal operating temperature — about 15 minutes. The ceramization reaction is driven by heat, so a cold engine is the wrong moment to apply.

02

Switch off and add Cerator

Turn the engine off, then add the correct dose through the engine oil filler cap. This is an oil additive — it does not go in the fuel tank.

03

Start the engine, do not drive

Restart and let it run for 15 minutes without moving the vehicle. This circulates the product through the lubrication system before any load is applied.

04

Drive gently, up to 124 miles

Drive normally but without labouring the engine for the first 124 miles (200 km), and do not exceed 3,000 RPM during this period.

05

Full protection at 932 miles

The ceramic-metal layer is fully formed after approximately 932 miles (1,500 km) of driving. After that, drive as you normally would.

Checking the oil level on a modern gasoline engine before treatment
Know your oil capacity before you dose — it is the number the tables are built on
Dosing

How much
do you need?

Dose is set by two numbers: how much oil your engine holds, and how many miles are on it. One box contains one applicator.

Cerator CS‑B / CS‑D and Ceramizator ONE BOOST

Engine mileageOil capacity 2.1–10.6 qtOil capacity 10.6–21 qtOil capacity 21–32 qt
0 – 62,000 mi½ applicator1 applicator2 applicators
62,000 – 186,000 mi1 applicator2 applicators3 applicators
Over 186,000 mi2 applicators3 applicators4 applicators

Original figures: 0–100,000 km, 100,000–300,000 km and over 300,000 km, against oil volumes of 2–10 L, 10–20 L and 20–30 L.

Ceramizator CS‑B / CS‑D POWER

Engine mileage1.1–3.2 qt3.2–5.3 qt5.3–7.4 qt7.4–12.7 qt
0 – 124,000 mi1234
124,000 – 249,000 mi2345
Over 249,000 mi3456

Number of applicators. Original figures: 0–200,000 km, 200,000–400,000 km and over 400,000 km, against oil volumes of 1–3 L, 3–5 L, 5–7 L and 7–12 L.

Ceramizator CS‑B / CS‑D ULTIMATE

PackageTreatsProtectionApplication
300 ml / 10.1 fl oz bottleUp to 5.3 qt (5 L) of engine oilApprox. 75,000 mi (120,000 km)One bottle, poured into the oil filler

Engines holding more than 5.3 quarts need the dose scaled up proportionally.

Good practice

Things worth
knowing first

  • Apply to fresh oil where possible — right after an oil change is the ideal moment
  • Any motor oil works: conventional, semi-synthetic or full synthetic
  • Safe for engines with catalytic converters and diesel particulate filters
  • Do not overdose. More product does not build a thicker layer; the reaction is self-limiting
  • Fuel additives (CP‑B, CP‑D) go in the fuel tank, not the oil
  • Keep following your vehicle manufacturer's oil-change schedule as normal
Ceramizator applicator being emptied into an engine oil filler neck

Not sure about your engine?

Oil capacity, mileage, fuel type and how the vehicle is used all matter. Send those details and a technical specialist will tell you which product and dose apply.